Discuss, share information, ask questions, and show off your expertise on Yoder Pellet Cookers.

Click the links below to go directly to available resources:
**Pellet cookers** - YS480, YS640
**Competition Pellet cookers** - YS480 Comp, YS640 Comp, YS1500 Comp, Cimarron Comp
**Pellet Cooker Warranty**
June 29th, 2015, 7:27 pm
#1
Site AdminSite Admin
User avatar
  • Joined: April 18th, 2014, 3:12 pm
  • Posts: 2408

The first thing to remember, is that the pellet cookers do NOT display the exact temperature in the cooker, but rather, display a 90 second running average of the temperature over time. So considering this, the controller display may never exactly match what an external probe displays. If the lid is left closed, no meat is in the cooker, and you are just reading temperatures, the longer the cooker is allowed to normalize, the closer the controller temperature will be to an external probe. Also, the controller temperature that is displayed is programmatically calculated to approximate the center of the lower cooking grates.

Here are some best practice points when reading temperatures with an external probe:
1. Verify your external probes in boiling water.
This will allow you to see if the probes are correct or how many degrees they are off of 212 degrees.
2. Never run external probes through the cooker door. Use a probe port or the chimney.
Running probes through the door disrupts the positive airflow in the cooker and will cause temp fluctuations.
3. Place the external probe directly on the cooking grate (not in a holder), just to the left of center of the lower cooking grates, with the tip centered front to back.
The is the approximation point for the controller when calculating the displayed temperature.
4. Never place anything within 6" of the probe.
The cold mass close to a temperature probe WILL affect the probe and cause erroneous temperature readings.
5. Never open the cooker's lid when verifying temperatures.
This will collapse the cooking environment, and cause a temperature loss which will require a recovery period.
6. Remove all foil, pans and trays from the cooker when verifying temperatures.
Foil, pans and trays in the cooker WILL affect the temperature readings.

Requirements for the proper functioning of the pellet cooker to achieve correct temperature readings:
1. It is a requirement that each cooking session start with plugging the cooker into power. If the cooker is already plugged into power, it MUST be unplugged for a minimum of 30 seconds and then plugged back into power, before starting a cooking session.
This resets the controller, like a cold boot for a computer.
2. It is a requirement that the burn grate fitment in the firebox be checked prior to each cooking session.
This is required maintenance outlined in the manual under Firebox and Burn Grate Assembly Maintenance. Here are the latest versions of the Yoder Smokers manuals: http://community.yodersmokers.com/viewtopic.php?f=49&t=153
3. It is a requirement that the silicone seals around the firebox be checked and maintained (see manual reference in #2).
This insures the proper function of the air delivery through the burn grate and insures an efficient fire.
4. It is a requirement that all ash be cleaned from the burn grate and firebox prior to each cooking session.
This explains why: http://community.yodersmokers.com/viewtopic.php?f=36&t=454
5. It is a requirement that the chimney be mounted flush with the inside wall of the cooker.
This allows proper scavenging of the heat and smoke from the cooking environment.
6. It is a requirement that the heat diffuser plate be centered front to back on the hopper end of the cooker.
This allows for the even distribution of heat and smoke into the cooking chamber.

Issues found to affect temperatures in pellet cookers:
-Excessive opening of the cooker lid during cooking.
Each time the lid is opened, the cooking environment is collapsed, and requires a recovery period.
-Warped heat Diffuser plate: http://community.yodersmokers.com/viewtopic.php?f=36&t=338.
-Spritzing/spraying/mopping liquid into the cooking environment during cooking.
This causes an evaporative cooling effect in the cooker which lowers temperatures and requires recovery time.
-Air flow from the cooker's fans:http://community.yodersmokers.com/viewtopic.php?f=36&t=354.
-Substandard pellets.
The Yoder factory uses BBQR's Delight for all testing and calibration.
-Moisture contaminated pellets.
Pellet bags are NOT moisture proof. NEVER store pellets directly on the floor. Pellets normally contain less than 10% moisture, and will absorb moisture from the air in an attempt to normalize with the moisture content of the environment they are stored in.

More Information:
-Here is an article on temperature: http://community.yodersmokers.com/viewtopic.php?f=36&t=83
-Here is an in depth article on the controller and temperature: http://community.yodersmokers.com/viewtopic.php?f=36&t=628
Here is the official Yoder pellet cooker temperature verification test: http://community.yodersmokers.com/download/Best%20Practice%20and%20how%20to/Yoder%20Pellet%20Temperature%20Test.pdf

Yoder_Herb
July 1st, 2015, 12:24 pm
#2
* Abilene ** Abilene *
  • Joined: August 25th, 2014, 10:00 am
  • Posts: 4
  • Location: Prague, Czech Republic

Thanks for this detailed report Herb. A pellet grill makes easy work out of barbecue, but it can also increase blood pressure if you worry too much about the display temp.

-Clint
European importers of Yoder Smokers
www.bbqeurope.com

Return to Pellet


cron