Page 1 of 1

640 Initial burn/seasoning

PostPosted: June 10th, 2016, 7:58 am
by Bosox1901
a little confused...is the initial burn a a step to be taken on its own, followed up with a completely separate seasoning process?
something like this....

1. wash and clean the grates and diffuser 1st, reinstall and run the unit at 350 for an hour or so.

OR

2. wash and clean the grates and diffuser and THEN coat them with oil, reinstall and run the unit at 350 for an hour or so

OR

3. wash and clean the grates and diffuser, no oil, burn at 350 for an hour or so,rewash and clean the grates and diffuser, reinstall, followed by a cook of something fatty like chicken, or bacon to complete the seasoning part of the equation

AND

4. also should the inside of the body be coated with oil, or will the seasoning take care of that?

Re: 640 Initial burn/seasoning

PostPosted: June 10th, 2016, 9:09 am
by Yoder_Kirby
Step one is what you need to do. Wash the grates then reinstall and run and empty cooker to burn off the unit and let cool. Then you can oil the grates and inside if you want to but it's not needed. After the burn off you can just cook and it will season itself as you cook.

Re: 640 Initial burn/seasoning

PostPosted: June 10th, 2016, 9:30 am
by Bosox1901
thanx for responding kirby...i appreciate it.

Re: 640 Initial burn/seasoning

PostPosted: June 10th, 2016, 10:05 am
by Yoder_Herb
The easy way:

- Get the smoker off the pallet
- Put everything in place in the cooker
- Load the hopper with pellets
- Plug it in and start it up at the default 350 degrees
- Let it run for a minimum of 1 hour
- Once completely cooled, wipe down the top and bottom of all the grates (make sure that they are completely dry when done)
- clean out all the ash in the burn grate, firebox and bottom of the cooker
- Using a spray can of canola oil, spray the top of the diffuser plate, and everything above it with a thick coat of oil (I do the chamber walls and the lid, but be careful to not create a mess, this is optional and does not need to be done, IF, food is immediately and continually cooked to achieve the same results)
- Unplug the power cord
- Wait 30 seconds
- Plug the power cord back in and start the cooker at the default 350 degrees
- Let it run for a minimum of 1 hour
- Start your new life with your new obsession

Re: 640 Initial burn/seasoning

PostPosted: July 28th, 2016, 12:20 pm
by Bosox1901
thanx herb, you could not have explained it any easier if you tried.

Re: 640 Initial burn/seasoning

PostPosted: November 16th, 2020, 4:34 pm
by Lidarius
Yoder_Herb wrote:The easy way:

- Get the smoker off the pallet
- Put everything in place in the cooker
- Load the hopper with pellets
- Plug it in and start it up at the default 350 degrees
- Let it run for a minimum of 1 hour
- Once completely cooled, wipe down the top and bottom of all the grates (make sure that they are completely dry when done)
- clean out all the ash in the burn grate, firebox and bottom of the cooker
- Using a spray can of canola oil, spray the top of the diffuser plate, and everything above it with a thick coat of oil (I do the chamber walls and the lid, but be careful to not create a mess, this is optional and does not need to be done, IF, food is immediately and continually cooked to achieve the same results)
- Unplug the power cord
- Wait 30 seconds
- Plug the power cord back in and start the cooker at the default 350 degrees
- Let it run for a minimum of 1 hour
- Start your new life with your new obsession



Is this still the correct and easy method. I am getting my YS640s tomorrow

Re: 640 Initial burn/seasoning

PostPosted: December 21st, 2020, 1:28 pm
by coachescrew
...Same question....getting it tomorrow as well.

What about First Cook....I am hearing it should be a Very fat/greasy type of meat. is this True? If so, what type of meat do folks recommend?

Thanks in advance and Happy Holidays.

Re: 640 Initial burn/seasoning

PostPosted: December 23rd, 2020, 12:44 pm
by curly
I would still use this exact process for the initial burn. My first cook was some pulled pork. Some guys try and keep their diffuser really clean and foil it but I like that mine is "seasoned" cast iron-ish. That's just a personal preference. Enjoy the new Yoder!

Re: 640 Initial burn/seasoning

PostPosted: December 23rd, 2020, 2:33 pm
by coachescrew
Tks. So we run it for 1 HR, shut it down and apply oil, then RESTART it for another hour?